Global standards for high-voltage connectors

Global standards for high-voltage connectors

In the International Standard Classification, high-voltage connectors relate to road vehicle devices, radiation measurement, electrical components, pipe components and pipes, floor treatment equipment, switchgear and controllers, mining equipment, transformers, reactors, inductors, road vehicle internal combustion engines, Nuclear energy engineering.

In the Chinese standard classification, high-voltage connectors relate to automotive electronics, electrical equipment and instrumentation, reactors, nuclear power plant safety power distribution equipment, hoses, tape, tape, household cleaning, whole containers, electronics, electrical equipment, high-voltage switchgear , Inductors, transformers, connectors, special equipment for coal mines, transformers, low-voltage power distribution appliances, intake and exhaust and fuel supply systems, general nuclear equipment.

The State Administration for Market Regulation and the National Standardization Administration of China, standards for high-voltage connectors

• GB/T 37133-2018 Technical requirements for high-voltage and high-current wiring harnesses and connectors for electric vehicles

State Administration of Quality Supervision, Inspection and Quarantine, standards for high-voltage connectors

• GB/T 5964-1986 High voltage coaxial connectors for nuclear instruments

Standards on high-voltage connectors

• SFS 2663-1975 Structure test of high voltage connector

German Institute for Standardization, standards for high-voltage connectors

• DIN EN 1829-2-2012 High-pressure water spray machinery. Safety requirements. Part 2: Hoses, hose lines and connectors
• DIN EN 62271-209-2008 High-voltage switchgear and controller. Part 209: Cable connectors for gas-insulated metal-enclosed switchgear with rated voltage higher than 52kV. Liquid-filled and extruded insulated cables. Liquid-filled and dry type Cable termination
• DIN EN 1829-2-2008 High-pressure water spray machinery. Safety requirements. Part 2: Hoses, hose lines and connectors

American Society of Motor Vehicle Engineers, standards for high-voltage connectors

• SAE/USCAR-37-2008 High voltage connector performance. Supplement to SAE/USCAR-2
• SAE J 1949-1988 Road vehicle high pressure fuel injection pump end connector 60Deg female cone wheel

Canadian Standards Association, standards for high-voltage connectors

• CSA C227.4-06 UPD 2-2007 Three-phase, gasketed distribution transformer with separable insulated high-voltage connectors
• CSA C227.4-06 UPD 1-2007 Three-phase, gasketed distribution transformer with separable insulated high-voltage connectors
• CSA C227.3-06-CAN/CSA UPD 1-2007 Low-section, single-phase, gasketed distribution transformer with separable insulated high-voltage connectors
• CSA C227.4-06-2006 Three-phase, mated distribution transformer with separable insulated high-voltage connectors. 2nd edition
• CSA C227.3-06-CAN/CSA-2006 Low-section, single-phase, gasketed distribution transformer with separable insulated high-voltage connectors. Fourth edition

European Committee for Electrotechnical Standardization, standards for high-voltage connectors

• EN 62271-209-2007 High-voltage switchgear and control equipment. Part 209: Rated voltage>52kv gas isolation metal-encapsulated switch cable connector. Liquid-filled and extruded insulated cables. Liquid-filled and dry-type cable terminals

U.S. Defense Logistics Agency, standards for high-voltage connectors

• DLA DSCC-DWG-89055 REV C-2006 No. 8 jack contact high voltage direct welding connector

Industry standards-coal, standards for high-voltage connectors

MT/T 947-2005 Flameproof high voltage cable connector for coal mine

American Institute of Electrical and Electronics Engineers, standards for high-voltage connectors

• IEEE C57.12.23-2002 Underground, self-cooling single-phase distribution transformers with separable insulated high-voltage connectors: high-voltage 25000V and below, low-voltage 600V and below, 167kVA and smaller transformers
• IEEE C57.12.23-1992 Underground type, self-cooling single-phase distribution transformer with separable insulated high-voltage connectors. High voltage (34,940GrdV/1400V) and below and low voltage (240/120V, 167kVA)
• IEEE C57.12.26-1992 Separate self-cooling three-phase distribution transformer installed on the base used with separable insulated high-voltage connectors. (34500GrdV/19920V and below, 2500kVA and below)
• IEEE 592-1990 Exposed semiconductor sheath of high-voltage cable joints and separable insulated connectors
• IEEE N 42.4-1971 High voltage connectors for nuclear instruments
• IEEE/ANSI N 42.4-1971 American National Standard for High Voltage Connectors for Nuclear Instruments

American National Standards Institute, standards for high-voltage connectors

• ANSI C57.12.25-1990 Transformer. The interval type self-cooling single-phase distribution transformer installed on the base with detachable insulated high voltage connector. The high voltage is not more than 34500Y grounding/19920V, the low voltage is 240/120V, and the capacity is not greater than 167 kVA. Requirements

British Standards Institute, standards for high-voltage connectors

• BS 6553-1984 Fuse Connector Selection Guide for High Voltage Fuses for Transformer Circuit Equipment

International Electrotechnical Commission, standards for high-voltage connectors

• IEC 60498-1975 High voltage coaxial connectors for nuclear instruments